AIAG PSW PDF

36, X. 37, X. 38, March , CFG, Blanket statements of conformance are unacceptable for any test results. 39, SIGNATURE, TITLE, DATE. PSW. AIAG Production Part Approval process PPAP 4th Edition Approval of Requirements Team of PPAP Submitted PSW Customer Process Design Requirements I. Hello, in the pdf I can see a new revision from PSW. Have a look at the previous post “AIAG PPAP (Production Part Approval Process).

Author: Kektilar Meztijin
Country: Norway
Language: English (Spanish)
Genre: Automotive
Published (Last): 9 November 2006
Pages: 158
PDF File Size: 2.93 Mb
ePub File Size: 14.43 Mb
ISBN: 722-2-43381-743-8
Downloads: 67179
Price: Free* [*Free Regsitration Required]
Uploader: Yolrajas

Customer part number if applicable. The term is also used by some other companies like Hyundai and Kia. Product Engineer’s signature, printed name, phone number, and date. Customer will probably not even notice the failure.

Pplcis an indicator of process performance psww on process variation throughout the full set of data. Acceptability of these facsimiles is to be confirmed with the authorized customer representative prior to the first submission. Use of these suggestions will arsive at the same end point of a completed Design FMEA, but with greater applicability to bulk materials. Process flow diagrams can apply to any aspect of the business. The date of these changes Additional Engineering Changes i.

Provide any explanatory comments on the Submission Results or any deviations from the Declaration. Fax number of the person signing the declaration.

Based upon similar products or processes and the potential failure model. This is very helpful to know when speaking to different department in the manufacturers company as not everyone will psd the suppliers part number. This weight is used for vehicle weight analysis only and does not affect the approval process.

Part Submission Warrant (PSW)

The specific cavities, molds, line, etc. Input the name and address of the company that idwill manufacture the component. At least one part shall be measured from each cavity, tool, line, or process used in product realization. For example, percent aiaag and viscosity of a bulk coating which impacts the final coating’s film build attribute, may be affected by the customer’s mix room percent solvent reduction.

  KARAVANOVA SURVIVAL RUSSIAN PDF

Level 2 – Warrant with product samples and limited supporting data submitted to customer. Records shown may be in various media and in various storage locations. Log In Sign Up. It is important that adequate quantities of parts be manufactured during this run to confirm the quality and capability of production process at rate prior to full production.

The Supplier Quality Requirements Task Force gratefully acknowledges the contributions of the many individuals and their respective companies that participated in the revision process.

A customer can formally waive PPAP requirements for an organization. The organization shall verify that all of the measurement and test results aia conformance with customer requirements and that all required documentation is available and, for Level 2, 3, and 4, is included in the submission as appropriate. The following figure provides a guideline for severity rankings. The next step provides an alternate method for assigning Detection rankings.

Parts from each unique production process, e. If production parts will be produced from more than one cavity, mold, tool, die, pattern, aiqg production qiag, e. The master sample shall be identified as such, and shall show the customer approval date on the sample. The following additional requirements are added: Unless approved by the authorized customer representative, attribute data are not acceptable for PPAP submissions.

AIAG Production Part Approval process PPAP 4th Edition | G C –

This does not imply pressure, mix rate, test protocol. April Learn how and when to remove this template message.

  LM339N DATASHEET PDF

Organizations supplying to subscribing truck Psd are required to complete the Product Process Change notification form to advise of forthcoming process or proprietary product changes. Select Champions for each team – these are the customer process owners i.

SAkEA – refers to the productlpast specified on the contract between the customer and organization. Identify by name or function the individual who will review and approve the element. AB CD Control temperature of mix. For guidance on items listed below, contact the authorized customer representative.

AAR typically applies only for parts with color, grain, or surface appearance requirements.

Production part approval process

Engineering released finished end item part name and number. October Learn how and when to remove this template message. Estimate the date that the Organization will have their internal qualifications complete. Enter the buyer’s name and code. Identify any qualifying information or references to attached documents that provide specific information regarding the element.

aaiag

When part size, sheer volume of parts, etc. The purpose of this requirement is to determine if the production process is likely to produce product that will meet the customer’s requirements. Infonnationldata based upon similar products or processes. Customer Use Only Customer Representative. Telephone number where person signing the declaration can be reached.

To be completed by authorized customer aiat not used by GM. The PPAP file shall contain the name of the authorized customer representative granting the waiver and the date. Engineering released customer part number. PPAP 4th Edition includes the following changes: